2010 Evinrude E-TEC Engine Specifications 40 50 60 65 HP

2010 Evinrude E-TEC Engine Specifications 40 50 60 65 HP

These specifications apply to the 2010 Evinrude E-TEC 40 50 60 65 horsepower outboard engines. It’s a precise and detailed description of the essential characteristics and components outlined by the manufacturer.

Engine Specifications 40 — 65 HP E-TEC Models

Full Throttle
Operating Range RPM
40 HP - 5000 to 6000 RPM
50 HP - 5500 to 6000 RPM
60 HP - 5500 to 6000 RPM
65 HP - 5500 to 6000 RPM 
Power 40 HP (30 kw) @ 5500 RPM
50 HP (37 kw) @ 5750 RPM
60 HP (45 kw) @ 5750 RPM
65 HP (45 kw) @ 5750 RPM

Idle RPM in Gear

800 ± 50 EMM Controlled

Idle RPM in Neutral

750 ± 50 EMM Controlled

Weight
(may vary depending on model)

(RL) Models: 232 lbs. (105 kg)
(PL) Models: 240 lbs. (109 kg)

Lubrication

Evinrude/Johnson XD100, XD50, XD30; or NMMA TC-W3 certified

Engine Type

In-line, 2 Cylinder, Two-Cycle

Displacement

52.7 cu. in. (864 cc)

Bore

3.601 in (91.47 mm)

Stroke

2.588 in. (65.74 mm)

Standard Bore

3.6005 to 3.6015 in. (91.45 to 91.48 mm)
To bore oversize, add piston oversize dimension to standard bore

Top Crankshaft Journal

2.1870 to 2.1875 in. (55.55 to 55.56 mm)

Center Crankshaft Journal

2.1870 to 2.1875 in. (55.55 to 55.56 mm)

Bottom Crankshaft Journal

1.5747 to 1.5752 in. (40.0 to 40.01 mm)

Rod Crankpin

1.3757 to 1.3762 in. (34.94 to 34.96 mm)

Piston Ring End Gap, Both

0.011 to 0.023 in. (0.28 to 0.58 mm)

Fuel Specifications 40 — 65 HP E-TEC Models

Fuel/Oil Control

EMM Controlled

Starting Enrichment

EMM Controlled

Minimum (High) Fuel Pressure

24 to 28 psi (165 to 193 kPa)

Minimum Fuel Lift Pump Pressure

3 psi (21 kPa)

Maximum Fuel Inlet Vacuum

4 in. Hg.

Minimum Octane

87 AKI (R+M)/2 or 90 RON

Additives

2+4 ® Fuel Conditioner, Fuel System Cleaner Use of other additives may result in engine damage.
Download repair manual for additional information

Electrical Specifications 40 — 65 HP E-TEC Models

Minimum Battery Requirements

640 CCA (800 MCA) or 800 CCA (1000 MCA) below 32° F (0° C)

 

Alternator

25-Amp fully regulated

Tachometer Setting

6 pulse (12 pole)

Engine Fuse

P/N 967545 – 10 A

Cooling Specifications 40 — 65 HP E-TEC Models

Thermostat

143°F (62°C)

Maximum Temperature

212°F (100°C)

Water pressure

11 psi minimum @ 5000 RPM

Ignition Specifications 40 — 65 HP E-TEC Models

Type

Capacitor Discharge

Firing Order

1-2

Ignition Timing

EMM Controlled

RPM Limit in Gear

6250

RPM Limit in Neutral

1800

Crankshaft Position Sensor Air Gap

Fixed

Spark Plug

Refer to Emission Control Information Label

Champion † QC10WEP @ 0.028 ± .003 in. (0.71 mm)

Gearcase Specifications 40 — 65 HP E-TEC Models

Gear Ratio

12:32 (.375)

Lubricant

HPF XR Gearcase Lube
HPF Pro in high performance or commercial applications

Capacity

22 fl. oz. (650 ml)

Shift Rod Height

20 in. (L) Models: 21.38 (543 mm) ± one-half turn

Shift Cable Stroke

1.125 to 1.330 in. (28.6 to 33.8 mm) measured between NEUTRAL and FORWARD

Power Trim/Tilt Specifications 40 — 65 HP E-TEC Models

Lubrication

Evinrude/Johnson Biodegradable TNT Fluid

Fluid Capacity

15.2 fl. oz. (450 ml)

Trim Range

0° to 15°

Tilt Range

16° to 65°

Models Include: E40DRLISD E40DTLISR E40DPLISD E40DSLISR E50DTLISR E50DPLISD E50DSLISR E60DTLISR E60DPLISD E60DSLISR E65WDRLISR E65WDRYISR E65WDRYISF

Be the first to comment

Leave a Reply

Your email address will not be published.


*